Skip to main content
Integrar IoT
Resource

Power Quality

Poor power quality costs millions in damage and penalties. Monitor it proactively.

Key Metrics

127th

Harmonics Order

50K

Events Captured

64

Samples/cycle

EN50160

Compliant

Why This Matters

Voltage Quality Is an Equipment-Lifetime Problem

Power quality describes how closely the delivered voltage matches a clean, stable sine wave. In practice, it is almost never clean: variable-speed drives, rectifiers, and switching power supplies all distort the waveform, and the grid itself injects sags, swells, and transients. The cost is paid in heat, derating, and premature failure of motors, transformers, and electronics.

The financial exposure is larger than most facilities teams assume. Harmonic current flowing through neutrals and transformers heats them, wasting energy and reducing the capacity of distribution equipment. Voltage sags - the most common power quality event - cause nuisance trips of process equipment and IT that can cost far more than the energy involved. In continuous-process industries, a single sag that stops a line can wipe out a year of electricity savings.

The point of monitoring is not to achieve a perfect waveform - that is impossible. It is to quantify the level of disturbance, catch the damaging events, and demonstrate compliance where utility or tenant agreements require it.

Standards

The Reference Frameworks

IEEE 519

Limits on voltage and current harmonics at the point of common coupling, the standard for industrial harmonic compliance

EN 50160

European voltage characteristics standard covering frequency, magnitude, harmonics, and interruptions

IEC 61000-4-30

Defines measurement methods and accuracy classes for power quality instrumentation

IEC 61000-4-7

Measurement technique for harmonics and interharmonics, referenced by IEEE 519 assessments

Deep Dive

Harmonics: The Steady-State Distortion

Harmonics are current or voltage components at integer multiples of the fundamental 50/60 Hz frequency. A variable-speed drive's rectifier stage draws current in pulses rather than smoothly, which produces 3rd, 5th, 7th, and higher harmonics. The 3rd harmonic is particularly problematic in three-phase systems because triplen harmonics (orders divisible by three) add in the neutral conductor, overheating a neutral that was never sized for full load current.

5%

IEEE 519 voltage THD limit most commonly applied at the service point (for <69kV systems)

3rd

Harmonic order that adds in the neutral and overloads shared neutrals

10-15%

Typical transformer derating observed with unfiltered nonlinear loads

Mitigation options are well established: line reactors and harmonic-rated drives reduce low-order current at the source, passive filters trap specific harmonics, and active filters cancel distortion dynamically. The correct choice depends on measured levels, not assumptions - which is exactly why monitoring comes first.

Deep Dive

Sags, Swells, and Transients: The Event Family

Where harmonics are a continuous condition, sags, swells, and transients are discrete events that must be captured at high resolution to be understood. A sag is a voltage dip typically lasting a few cycles to a few seconds - caused by large motor starts or grid faults elsewhere. A swell is the opposite, and a transient is a short, high-energy spike or notch lasting microseconds to a few milliseconds. None is visible to a standard utility meter, which is why dedicated PQ analysis is required.

EventDefinitionCommon CauseTypical Impact
Voltage sagRMS voltage drops 10-90% for 0.5 cycle to 60sMotor starting, grid faults, transformer switchingIT resets, process trips, contactor dropout
Voltage swellRMS voltage rises 110-180% for 0.5 cycle to 60sSingle-phase faults elsewhere, load sheddingPower supply stress, electronic damage
TransientShort voltage spike or notch, microseconds to msLightning, switching, capacitor banks, VFD commutationSilicon damage, nuisance alarms, data corruption
InterruptionSupply below 10% for longer than 60sProtection operation, grid incidentsFull load loss, restart costs, process loss

Capturing these events requires instrumentation with waveform sampling - typically 128 samples per cycle or better - and event-triggered recording. The value is correlation: when a process trips, the PQ log shows whether the trip followed a sag or transient, converting a mystery into a root cause.

Best Practices

Designing a Power Quality Monitoring Plan

The goal of a PQ monitoring plan is not maximum instrumentation but targeted visibility at the points where compliance is judged and damage is felt.

Step 1

Measure at Boundaries

Instrument the utility service point and each transformer feeding critical or nonlinear loads. IEEE 519 compliance is assessed at the point of common coupling.

Step 2

Match Accuracy to Need

Use revenue-grade meters (IEC 61000-4-30 Class A) where compliance evidence matters; lower classes only where you need trend, not proof.

Step 3

Baseline Three Months

A quarterly baseline captures seasonal load shifts and reveals the recurring harmonic profile before any mitigation spend is approved.

Step 4

Correlate to Events

Join PQ logs with production, IT, and equipment-failure records so each captured event is tied to a consequence and a cost.

Evaluation Checklist

  • Confirm the instrument captures full waveforms, not just RMS summaries, for event analysis
  • Define IEEE 519 evaluation criteria per site before monitoring starts
  • Log sag thresholds tuned to your sensitive loads' actual immunity curves, not generic defaults
  • Verify data retention spans a full year so seasonal harmonics and utility incidents are captured

Protect Your Equipment from Power Disturbances

Talk to our power quality engineers about instrumenting your service entrance and critical loads.

Get Started